UV Disinfection Consumables

UV Lamps, Ballasts & Quartz Sleeves

UV lamps, electronic ballasts, quartz sleeves and UV sensors for low-pressure, TOC and medium-pressure UV systems. Parts are selected by equipment model, power, wavelength, dimensions and operating conditions.

Discuss Your Requirement →

Range of KONCHE UV consumables: germicidal lamps, ballasts, quartz sleeves and UV sensors

KONCHEINDUSTRIAL WATER TREATMENT SYSTEMSMODEL KONCHE UC · UV CONSUMABLESREACTOR-MATCHEDDOSE SAFEREPLACEMENT PLANENGINEERED BY KONCHE · 2026

QUICK TECHNICAL ANSWER

What are UV Disinfection Consumables?

KONCHE UV consumables: genuine lamps, electronic ballasts, quartz sleeves and sensors for 254 nm disinfection and 185 nm TOC stages — stock-supplied with technical selection support.

What it delivers

Stable UV output — high 254 nm transmission keeps microbiological compliance reliable
Ballasts with full protection reduce flicker, power fluctuation and lamp failure
Stock supply with same-day dispatch cuts disinfection downtime

Why trust KONCHE

UV equipment manufactured since 1997 — consumables specified by the equipment builder
Selection support matches lamp power, length and cap type to your unit
Intensity test report provided after guided replacement

Where we stand out

What matters to you	How KONCHE delivers
Stable disinfection	High-transmission genuine lamps keep dose on target
Long lamp life	8,000–10,000 h low-pressure; 8,000–10,000 h medium-pressure
Fit-all adaptation	Low-pressure, TOC and medium-pressure units of any brand
Fast response	Stock in Shenzhen with same-day dispatch

Explore: All consumables · General consumables

PRODUCT DOCUMENTATION

UV disinfection consumables are the replacement lamps, quartz sleeves, ballasts and seals that keep 254 nm and 185 nm UV systems at their validated dose. The KONCHE UV consumables programme supplies lamp-and-ballast power classes from 10 W to 1,000 W for 254 nm disinfection, 185+254 nm TOC stages and broad-spectrum medium-pressure duties. The range includes conventional low-pressure lamps (10–80 W), low-pressure high-output / amalgam lamps (50–1,000 W), medium-pressure lamps (200–1,000 W), TOC-degradation lamps, matching electronic ballasts (10–1,000 W with over-current, over-voltage, short-circuit and over-temperature protection), G10Q wired lamp holders, custom quartz sleeves and 254 nm intensity sensors. A 1,000 W rating alone does not define lamp pressure: both low-pressure amalgam and medium-pressure configurations are available, so every replacement is confirmed against spectrum, lamp current, starting mode, dimensions, cap and reactor model. All parts are selected for KONCHE and mainstream-brand UV equipment with technical selection support. Typical users: ultrapure-water systems, pharmaceutical GMP loops, food and beverage lines, municipal and school drinking water, electronics and PCB plants, and pools.

PRODUCT CATEGORIES

Category	Specification	Typical application
Conventional low-pressure UV lamps	10–80 W, 254 nm	Flow-through low-pressure sterilizers
Low-pressure high-output / amalgam lamps	50–1,000 W, 254 nm or 185+254 nm	High-output disinfection and oxidation systems
Medium-pressure UV lamps	200–1,000 W, broad-spectrum 200–400 nm	Compact high-intensity and pool/process-water systems
TOC-degradation lamps	185+254 nm dual band	TOC UV degradation units
Electronic ballasts	10–1,000 W, lamp-matched	Matched power supply for the specified lamp technology
G10Q wired lamp holders	Four-pin ceramic holder with application-matched leads	Water-treatment germicidal lamp connection
Quartz sleeves	Custom diameter, length and end configuration	UV lamp isolation and protection in the reactor
UV sensors	254 nm intensity	Online dose monitoring

PRODUCT DATA

Part	Reference	Typical life / selection note
Conventional low-pressure lamp	10–80 W, 254 nm	8,000–10,000 hours
Low-pressure high-output / amalgam lamp	50–1,000 W, 254 nm or 185+254 nm	Confirmed against the selected lamp specification
Medium-pressure lamp	200–1,000 W, 200–400 nm	8,000–10,000 hours, subject to lamp and system
TOC lamp	185 nm + 254 nm	8,000–10,000 hours, subject to system
Electronic ballast	10–1,000 W; matched by current, voltage and starting mode	Approximately 3–5 years
G10Q wired lamp holder	Four-pin ceramic connection; lead length and wiring matched to equipment	Inspect during every lamp replacement
Quartz sleeve	Matched by outside diameter, length, wall thickness and end form	Approximately 2–3 years
UV sensor / probe	Matched to controller	According to calibration and condition

APPLICATIONS

Industry	Water point	System value
Pure / ultrapure water	TOC lamp replacement	Keeps TOC on specification at the loop end.
Pharmaceuticals	GMP purified-water loops	Compliant flow-through UV lamps.
Food and beverage	Process water	Lamps and ballasts to food-safety standard.
Municipal / school water	Direct drinking stations	Low-pressure lamps protecting drinking safety.
Electronics / PCB	Chip cleaning water	TOC lamps meeting cleaning requirements.
Pools	Circulating water	Medium-pressure lamps, strong kill with fewer chloramines.

REPLACEMENT CYCLES

Consumable	Recommended cycle	Replacement criterion
Low-pressure UV lamps	8,000–10,000 h	Intensity below 70% of initial
Medium-pressure UV lamps	8,000–10,000 h	Intensity drop or lamp blackening
TOC-degradation lamps	8,000–10,000 h	TOC removal efficiency decline
Electronic ballasts	3–5 years	Flicker, no-light or unstable power
Quartz sleeves	2–3 years	Fouling or scaling reducing transmission

SUPPLY & SERVICE

Advantage	Customer benefit
Stable UV output	High 254 nm transmission keeps microbiological results reliable.
Smooth ballast operation	Stable drive reduces flicker and power fluctuation, extending lamp life.
Complete range, wide fit	Covers flow-through, TOC and medium-pressure units of any brand.
Stock with fast response	Same-day dispatch reduces disinfection downtime.
Technical selection support	Matched to equipment model and power requirements.
Fewer equipment faults	Genuine matched parts cut accessory-related failures.

FAQ

How do I order the correct UV lamp?

Send the system model, lamp marking, power, wavelength and a photo of the existing lamp or nameplate.

Why does the lamp still light but need replacement?

UV output can fall even when visible light remains. Replacement should follow operating hours and intensity monitoring.

How often should quartz sleeves be cleaned?

A common reference is every three months, adjusted for water hardness, iron, turbidity and deposits.

Can one ballast be used for different lamps?

Only when power, current, starting mode, dimensions and controller compatibility are confirmed. Do not assume interchangeability.

WHY KONCHE

Nearly 30 years of UV expertise

Since 1997, Konche has built UV disinfection equipment and supplied its consumables — lamps, ballasts and sleeves specified from the equipment builder perspective.